Car-audio-wiring-me-do

From: ANT_THOMAS12 Nov 2013 07:52
To: koswix 5 of 23
What colour is it?
From: Chris (CHRISSS)12 Nov 2013 09:04
To: koswix 6 of 23
I think nearly every time I've helped someone pur a car stereo in the power cables have been the wrong way round. Normally you'd have two fatter cables, one 12V permanent and one 12V that is switched with the ignition.
From: koswix12 Nov 2013 09:29
To: ANT_THOMAS 7 of 23
Can't recall exactly, either red or blue & red.
From: koswix12 Nov 2013 09:30
To: Chris (CHRISSS) 8 of 23
Aye, that was the initial problem. They're then correct way round now but still getting odd behaviour. Disconnecting permanent power means nothing works at all, even with the ignition on.
From: Chris (CHRISSS)12 Nov 2013 09:45
To: koswix 9 of 23
What happens if you swap them around? Does it stay on all the time?
From: Dan (HERMAND)12 Nov 2013 10:03
To: ALL10 of 23
Some stereos will take a feed from the light switch to change the display brightness at night. However, to be honest, it sounds like you have an actual issue with your wiring - all vehicle electrics should be at ~12-14 volts, anything less indicates a problem with voltage drop. Often a bad ground, a bad contact or even a short.

Remember, also, that current isn't restricted normally - the device will pull whatever power it needs, and if the wiring is designed for low current, then there should be a lower rated fuse to blow. As you're not blowing fuses, it sounds like a voltage problem.
EDITED: 12 Nov 2013 10:05 by HERMAND
From: koswix12 Nov 2013 10:04
To: Chris (CHRISSS) 11 of 23
It tries to stay on but doesn't seem to have enough juice yo boot up (perhaps because it needs both pins to have power? I dunno)
From: koswix12 Nov 2013 10:04
To: Chris (CHRISSS) 12 of 23
It tries to stay on but doesn't seem to have enough juice yo boot up (perhaps because it needs both pins to have power? I dunno)
From: ANT_THOMAS12 Nov 2013 10:05
To: Dan (HERMAND) 13 of 23
Your permanent should definitely power it just fine. As Dan said, sounds like a few issues with wiring. Or some odd extra wires that the car provides that aren't needed.
From: Chris (CHRISSS)12 Nov 2013 10:50
To: koswix 14 of 23
Have you checked the two main power lines are 12V?
From: koswix12 Nov 2013 16:03
To: ANT_THOMAS 15 of 23
Think I've fixed it. There was a permanent 12v coming in from the antenna motor pin. That's supposed to be an output pin from the radio to the antenna motor so was probably playing merry hell with the circuit. Snipped the wire and seems to be working correctly now.
From: ANT_THOMAS12 Nov 2013 16:49
To: koswix 16 of 23
Yeah, I can't imagine that was doing you any favours.
From: Chris (CHRISSS)12 Nov 2013 18:00
To: koswix 17 of 23
Your welcome.
From: koswix12 Nov 2013 18:04
To: Chris (CHRISSS) 18 of 23
What about my welcome ect
From: Chris (CHRISSS)12 Nov 2013 23:12
To: koswix 19 of 23
Maybe you forgot to plug it in.
From: koswix13 Nov 2013 01:47
To: Chris (CHRISSS) 20 of 23
I think I need to up the agp voltage.
From: Chris (CHRISSS)13 Nov 2013 01:49
To: koswix 21 of 23
2GB TBH.
From: koswix13 Nov 2013 09:38
To: Chris (CHRISSS) 22 of 23
Heh, that's actually the size of SD card I was going to put in it :-D
From: Chris (CHRISSS)14 Nov 2013 01:13
To: koswix 23 of 23
Trig would be proud :D